Haas CNC Dimensions, Model by Model, as Used Machines Really Ship
Typical as-shipped dims, weights, extra pieces and the one trailer each used Haas needs, pulled from real shipments we quoted out of Los Angeles and nationwide.
Every number here comes from used Haas CNC machines moving in the secondhand market, shipped uncrated from seller to buyer, usually on a skid or straight on the deck. These are not new, factory crated machines, which ship at different dims.
Used Haas CNC Shipping Starts With the Right Dims
Haas CNC dimensions are the first thing a carrier needs, and the first thing that is usually wrong on a quote request. This cheat sheet is based on 1,589 machine moves, with model data from used Haas shipments we quoted between April and October 2026. It covers 38 models, the chip pans and conveyors that showed up with them, and the one trailer each machine needs.
Dealers, buyers, riggers, freight forwarders and sellers can use it to sanity check a listing, plan floor space, or fill in a quote form without guessing. For how we plan the whole move, see our CNC machinery transport page.
How to Read These Numbers
Every figure is typical as shipped, confirm with your rigger. These are sizes shippers and sellers sent us for real used machines, not Haas factory specs, and two machines with the same model name can ship very differently.
- Dims are length x width x height of the machine itself. Weights leave out chip pans, coolant tanks and pallets.
- Lots of requests list a VF‑2, Mini Mill or TM‑0P as a 100 inch cube at 9,000 lbs. That is a placeholder someone typed in, not a measurement.
- Year, options, pallet systems and how the rigger skids the machine all change the real numbers.
- Some weights ran wide. Mini Mills mostly came in at 3,400 to 6,000 lbs, but a few quotes said 8,000 to 9,000. One VF‑3SS was quoted at 8,600 lbs while the seller's email for the same machine said 13,500.
We also cross-checked against used Haas listings from MachineStation. Where a listing and our shipping data disagree, the table keeps the as-shipped number. A used VF‑4 listing, for example, showed about 152" x 99" x 106" at 11,720 lbs, longer and lighter than the VF‑4 we quoted, so confirm with your rigger. Current factory specs live on the Haas Automation website.
Haas CNC Dimensions Table by Series
Tap a series or search a model. On a phone, swipe the table sideways.
| Model | Typical L x W x H | Weight (lbs) | Extra pieces seen | Trailer |
|---|---|---|---|---|
| VF Series Vertical Mills | ||||
| VF-2, VF-2SS, VF-2SSYT | About 8'5" x 8'3" x 8'8" when measured | 7,800 to 8,000 | Chip pan 7' x 6' x 3', about 1,000 lbs; some have a 4' x 3' x 3' coolant tank, about 500 lbs | Step Deck |
| VF-2D | 8'5" x 8'2" x 8'6" | 8,000 | Coolant tray, chip pan, 4' x 4' pallet | Flatbed |
| VF-2BYT | About 7'6" x 7'2" x 7'11" (reference listing, ours were placeholders) | About 8,000 (reference) | Chip pan 7' x 6' x 3' | Flatbed |
| VF-3 | 12'11" x 8'3" x 8'10" | 11,900 to 12,000 | Chip pan or conveyor 7' x 6' x 3', about 1,000 lbs | Step Deck |
| VF-3BYT | 11'3" x 8'4" x 8'9" | 12,000 | Parts skid 7' x 6' x 3' | Step Deck |
| VF-3SS | 11'3" x 8'4" x 8'6" | 12,500 (one seller said 13,500) | Chip pan | Flatbed |
| VF-3SSYT | 13'4" x 8'6" x 9'1" | 15,000 | None listed | Step Deck |
| VF-4 | 10' x 8' x 9' | 12,500 | Chip pan 7' x 6' x 2'6" | Step Deck |
| VF-4SS | 10'11" x 8'6" x 9'1" | 13,500 | Chip pan, 4' x 4' skid | Step Deck |
| VF-5 | 14'7" x 8'6" x 8'1" | 16,000 | Chip pan | Flatbed |
| VF-5SS | 14'2" x 8'4" x 9'1" | 13,000 to 14,600 | Chip pan, skid, coolant tank | Step Deck |
| VF-7 | 17'11" x 8'6" x 10'8.5" | 23,000 | Chip pan, small parts | Step Deck |
| VF-6/50 | 16'3" x 8'6" x 11' | 25,500 | Parts | Step Deck |
| UMC and EC Machining Centers | ||||
| UMC-500 | 9' x 8'2" x 8'8" | 12,000 | Coolant tank, chip conveyor | Step Deck |
| UMC-70 | 12' x 9'2" x 10'4" | 16,000 | None listed | Step Deck |
| UMC-750 | 14'2" x 9'7" x 10' (with pallet system) | 18,000 to 20,000 | Chip pan, tooling crate, pallet system | Step Deck |
| EC-400PP | 18'4" x 8'6" x 9'10" | 23,000 | Pallet pool 16'8" x 8'4" x 8'4", about 10,000 lbs; chip pan | Step Deck |
| TM Toolroom Mills | ||||
| TM-0P | Placeholder only, measure it * | 5,000 | None listed | Flatbed |
| TM-1 | 7'1" x 7'1" x 7'1" | 5,000 | None listed | Flatbed |
| TM-2 | 7'11" x 7'6" x 7'6" | 4,500 to 6,000 | 4' x 4' pallet | Flatbed |
| TM-2P | 10'10" x 6'8" x 8'4" | 6,000 | Chip pan 7' x 5' x 3' | Flatbed |
| Mini Mills | ||||
| Mini Mill | Most 7' to 7'11" per side | 3,400 to 6,000 (most) | 4' x 4' skid, chip pan | Flatbed |
| Mini Mill 2 | 7'8" x 6'8" x 8'1" | 4,200 | None listed | Flatbed |
| Super Mini Mill 2 | About 7'1" x 7'9" x 8'7" (reference listing, ours were placeholders) | 4,000 | 4' x 4' pallet | Step Deck |
| ST, SL, TL and CL Lathes | ||||
| ST-10Y | 10'6" x 5'11" x 6'11" | 7,900 | Coolant tank, tooling pallet | Flatbed |
| ST-15 | 11'11" x 7'6" x 6'6" | 8,000 to 11,000 | Coolant pan 6' x 4' x 3', about 1,000 lbs | Flatbed |
| ST-20Y | 11'11" x 7'6" x 6'6" | 11,000 | Coolant pan 6' x 4' x 3', about 1,000 lbs | Flatbed |
| ST-25Y | 14'3" x 7'6" x 8'2" (with conveyor) | 10,000 to 14,300 | Conveyor 10'9" x 3'3" x 7'2", coolant pan | Flatbed |
| ST-30M | 15' x 8'4" x 8'4" | 13,000 | Bar feeder, chip pan | Flatbed |
| ST-35Y | 12'6" x 7'6" x 7'6" | Confirm | Chip pan | Flatbed |
| ST-40 | 19'7" x 8'5" x 8'5" | 27,000 | Chip conveyor 15'5" x 4' x 4' rides separately | Flatbed |
| ST-45 | 19'2" x 8'4" x 8'4" | 28,000 | Chip pan | Flatbed |
| SL-20T | 10'7" x 6'2" x 6' | 9,000 | Chip pan | Flatbed |
| TL-1 | 7' x 3' x 6'8" | 3,950 | None listed | Flatbed |
| CL-1 | 6'8" x 6'8" x 6'8" | 3,000 | Bar feeder 7' x 2' x 3'6" | Flatbed |
| Rotary Tables | ||||
| HRT-160SS | 1'11" x 1'7" x 1'7" | 300 | Usually rides with the mill | Flatbed |
* Placeholder: our quotes for this model only used the 100 inch cube estimate. Rows marked reference listing fill a gap with figures from a MachineStation used Haas listing. Rows with one number come from one or two quotes, so use them as a starting point.
Flatbed or Step Deck: The 8'6" Rule
Height picks the trailer. Over 8'6" (102 inches) tall as it sits on the truck means a step deck. At 8'6" or under, it rides a flatbed.
Mini Mills, TM mills, VF‑2D, VF‑2BYT, VF‑3SS, VF‑5 and every lathe in the table.
VF‑2 class mills that measure over 8'6", VF‑3, VF‑3BYT, VF‑3SSYT, VF‑4, VF‑4SS, VF‑5SS, VF‑7, VF‑6/50, Super Mini Mill 2, the UMC series and the EC‑400PP.
A flatbed deck sits about 5 feet off the ground, so a machine taller than 8'6" pushes the load past the 13'6" height limit used in many states. A step deck's lower deck sits about 42 inches up, which buys that room. Width is a separate question: anything over 8'6" wide, like a UMC‑70 at 9'2", is oversize and can need permits on either trailer. Our oversize permit guide by state covers that.
Smaller used machines often share the deck as a partial truckload, which can reduce the cost of reserving a whole trailer when suitable shared capacity is running your way. The tradeoffs are a less fixed schedule and extra stops. Compare deck heights on our trailer types page.
Haas VF‑2 Dimensions: Why the 100 Inch Cube Is Wrong
Haas VF‑2 dimensions cause more confusion than any other model on this list, because so many requests use the same 100" x 100" x 100", 9,000 lb guess.
When shippers actually measured a used VF‑2, VF‑2SS or VF‑2SSYT, the machine came in around 8'5" long, 8'2" to 8'3" wide and 8'5" to 8'8" tall, at 7,800 to 8,000 lbs. That puts the taller units just over the 8'6" line, so they plan as a step deck, while a VF‑2D at 8'6" stays on a flatbed. A few inches change the trailer, so measure to the highest point as the machine will sit on the deck, including anything mounted on top.
Chip Pans, Coolant Tanks and Conveyors Ship as Their Own Pieces
Almost every used Haas mill we quoted came with at least one extra piece, and each needs deck space and a weight on the quote.
- Chip pan: the standard VMC add-on, usually 7' x 6' x 3' (sometimes 2'6" tall) and about 1,000 lbs.
- Coolant pan on lathes: ST‑15 and ST‑20Y units usually had a 6' x 4' x 3' pan at about 1,000 lbs.
- Coolant tank or tray: some VF‑2SS, VF‑2SSYT and VF‑2D units had a 4' x 3' x 3' tank at about 500 lbs instead.
- Chip conveyors on big lathes: often separate. One seller said the conveyor on an older ST‑40 rides on its own, at 15'5" x 4' x 4'.
- Bar feeders, pallet pools and tooling crates: list each one. An EC‑400PP pallet pool alone was quoted at about 10,000 lbs.
Air-Ride and a Dry Tarp Job
Every Haas quote we handled asked for an air-ride trailer, and most asked for the machine to be fully tarped.
Air-ride takes the edge off the road shock that reaches spindles, ways and electronics. That is why one shipper turned down hotshot gooseneck trailers, which often run spring suspension. If someone offers a hotshot for a Mini Mill, ask about the suspension first.
A tarp only protects a machine that goes under it dry. One damage dispute we saw came down to rust and water found at delivery, even though photos showed the machine tarped all the way to the deck. Water left in or on the machine before tarping was raised as the likely cause. Drain the coolant, wipe it down and let it dry before the driver covers it.
Rigging and Securement Notes
Plan the lift at both ends before the truck is booked, and talk through securement with the carrier.
- Dunnage goes under the base, then the base gets chained. On one load the driver showed up without dunnage and the riggers had to supply it, so ask who is bringing it.
- Not every used machine has lifting points. One ST‑40 had no eye bolts for a crane and needed a forklift.
- Some receivers want the machine at the back of the deck so two forklifts can lift it while the truck pulls out from under.
- Lots of moves go rigger to rigger, or the machine waits in a rigger's yard until the shop is ready.
The motor carrier and driver evaluate and maintain securement, and the shipper and riggers provide accurate weights, dims and a machine that is ready to handle. The FMCSA cargo securement rules are the baseline. For a real example, read how we coordinated Haas Mini Mill transport to Laredo.
Where to Buy or Sell a Used Haas
Buying or selling a used Haas CNC? These are good places to start, and every one of them will want accurate dims for the freight side.
- Haas Automation official site
Factory specs and Haas Factory Outlet contacts. - MachineStation used CNC machines
Used Haas mills and lathes with listed dims and weights. - Exapro used machinery marketplace
A marketplace for buying and selling used machine tools. - CNCMachines.com used CNC listings
Listings of used CNC machines from sellers and dealers.
What to Send for a Used Haas Shipping Quote
A quote is only as good as the details behind it. Send these and we can match the trailer the first time.
- Exact model and year, plus a photo of the data plate
- Measured L x W x H and weight as the machine will sit on the truck
- Every extra piece (chip pan, coolant tank, conveyor, bar feeder, pallets) with dims and weight
- Pickup and delivery city and state, and whether each end has a dock, forklift or rigger
- Anything mounted on top, or anything that cannot get wet
- Your timing, and whether the machine can wait at a rigger's yard
Haas CNC Dimensions FAQ
What are typical Haas VF‑2 dimensions for shipping?
When shippers measured used VF‑2 class mills for us, they ran about 8’5″ long, 8’2″ to 8’3″ wide and 8’5″ to 8’8″ tall, at 7,800 to 8,000 lbs. Plenty of requests just say 100 x 100 x 100 inches at 9,000 lbs, which is a placeholder, not a measurement. Treat every number as typical as shipped and confirm with your rigger.
When does a used Haas need a step deck instead of a flatbed?
If the machine is over 8’6″ (102 inches) tall as it sits on the truck, it goes on a step deck. At 8’6″ or less, it goes on a flatbed. A flatbed deck sits about 5 feet up, so a taller machine pushes the load past the 13’6″ height limit used in many states.
Are these Haas CNC dimensions factory specs?
No. They come from used Haas machines we quoted moving seller to buyer, usually uncrated on a skid. A factory crated new machine ships at different dims, so check the data plate and measure.
Does the chip pan ship with the machine?
Usually on the same truck, but as its own piece. On VMCs it is commonly about 7′ x 6′ x 3′ and 1,000 lbs, so list it on your quote request.
Can a hotshot haul a used Haas Mini Mill?
Every Haas quote we handled asked for air-ride, and many hotshot gooseneck trailers run spring suspension. Ask about the suspension before you accept a hotshot.
Got a Used Haas to Move?
Send the model, measured dims and weight, every extra piece, photos and both cities. We will match the trailer to the machine, work with your riggers on both ends, and keep you posted until it is on the floor.
IZ Freight is an independent agency of Armstrong Transport Group, LLC (MC-555609, USDOT 2236080). Transportation is performed by authorized motor carriers.
